Introduction

Quest QA Series power amplifies are built to work hard inthe tough environment of pro audio.

Industrial spec multi-speed fans and generous heat sinks will keep the output stage cool even if the amplifier is installed in a dusty and poorly ventilated area.

Service and maintenance is easy as the internal architecture is laid out for easy access by a qualified technician.

The sonically superior output stage is composed of a generous abundance of output devices for greater electronic stability and sonic fidelity.

QA series amplifiers are manufactured to a standard accepted as desirable practice for a concert standard power amplifier.

Heavy gauge welded 16-gauge steel chassis with vibration proof fittings, and an emphasis on over-engineering, guarantees years of trouble-free service in the most demanding environments.

Quest set about a design and layout for easy service, noteasy manufacture.

A minimum of disassembly is required for testing and maintenance meaning lower operating costs and longer amplifier life.

Features

  • Input Stage:
    • Pro active protection senses stages of system function to safeguard your investment both on turn on and while under operation.
    • Silent switch on/off circuitry reduces potential speaker damage in the event of intermittent power.
  • Power supply:
    • The high current power supply is manufactured to function reliably at high temperatures and well exceeds industry standards.
    • This results in smooth bass response and considerable dynamic headroom.
  • Industrial Spec
    • Fans: Dual heavy duty cooling fans guarantee long life of all electronic components.
  • Input Connection:
    • XLR parallel male and female input connections calibrated for most pro spec system controllers and electronic cross-overs. features
  • Speakon Connections:
    • International AES standard Speakon connectors wired for two channel and Bridge mono operation simplify speaker connections.
  • Limiter:
    • A switchable high speed limiter acts as a final speaker protection but can be disconnected where sensing speaker system controllers are required.
  • Built in switchable X-overs:
    • High Amplification and low pass filters on each channel make the versatile QA series even more flexible witha sub-mid/high frequency dividing network.
  • Selectable Gain settings:
    • Adjustable input switching for 0.775V, 32 dB or 26dB make system calibration easy.
  • Easy access air filters:
    • User serviceable air filters are easy to maintain for trouble free operation.

Note The QA Series Power Amplifiers are not Bridgeable

 

SPECIFICATIONS:

QA1004 Stereo Power Amp

QA2004 Stereo PowerAmp

 

 

2x 575-w at 4O 2x 870-w at 4O    
  • Rated Power
    (2x 8O):
290-W per channel @ 1kHz at <0.1% T.H.D. both channels driven 490-W per channel @ 1kHz at <0.1% T.H.D. both channels driven    
  • Rated Power:
    (2x 4O):
575-W per channel@ 1kHz at <0.1%T.H.D. both channels driven 870-W per channel @ 1kHz at <0.1% T.H.D. both channels driven    
  • T.H.D:
<0.1%@250-W per channel from 20 HZ to 20kHz <0.1%@400-W
per channel from 20 HZ to 20kHz
 
  • Minimum Load Impedeance:
2O - Audio signal / 4O - Signal wave
  • Phase Response:
+5 to -15 from 20 Hz to20kHz  
  • Input Impedance:
20 kO, balanced; 10 kO, unbalanced
  • Cooling:
Two temperature dependant variable speed 80mm high-output DC fans  
  • Controls:
Two front panel attenuators, rear panel mode switch and gain select switch
  • High Pass:
Linkwitz-Reily (24 dB/Octave): Off/35/80 Hz
  • Low Pass:
Linkwitz-Reily (24 dB/Octave): Off/80/110Hz
  • Voltage Gain @
    0.775-V:
29 dB or 24 dB 32 dB or 26 dB    
  • Crosstalk:
>-60 dB @ 1kHz at rated power @ 8O
  • Hum and Noise:
>-105 dB, "A" weighted referenced to rated power @ 8O >-107 dB, "A" weighted referenced to rated power @ 8O
  • Slew Rate:
>30V/us    
  • Damping factor (8O):
>500:1 @ 20Hz - 1kHz >700:1 @ 20Hz - 1kHz  
  • Indicator LEDs:
Two clip, two signal presence, one active status, two protection
  • Protection:
Thermal, DC, turn-on bursts, subsonic, incorrect loads
  • Connectors:
XLR . Speakon . 240/230Volt 16 amp IEC mains
  • Construction:
Cold Steel Rolling + Machined aluminium front panel
  • Dimensions (HxWxD):
89mm x 483mm x 496mm  
  • Net Weight:
17kg 21kg    
  • Packaged Shipping Weight:
20kg 23kg    

 

 

(QA1004)

12 Months
SKU QA1004
Model # QA 1004
Barcode # 9331001001200
Brand QUEST
Unit Of Measure Each
Assembled Width 18.500m

Be The First To Review This Product!

Help other Bourne Superstore users shop smarter by writing reviews for products you have purchased.

Write a product review

More From This Category